I spent some time taking apart my Roomba to remove some extra weight. You can see the pictures of this process here.
In the pictures, you can see my laptop with the tear-down instructions found here (click on the Discovery Breakdown link on the right). They were quite simple to follow and worked great. In the end, I removed the brush deck, side brush, cliff sensors (broken anyway), and the front bumper. I'll probably eventually remove the wheels and wheel drop sensors in order to drop some more weight. I also have a little better understanding of where I can "plug in" to the sensors for later in the project.....
I stopped by Fry's and picked up an Antec Tri-Cool 120mm case fan (about $14 after taxes). And a 9v battery for my multimeter. I picked the Tri-Cool because it had decent CFM (79 at 12v), would work at lower voltages (as low as 5v), and wasn't overly expensive. After I got my meter working, it probably didn't matter about the low voltage, turns out that the dust bin connector is putting out between 14 and 15 volts.
I tried to get the bathroom scale to work (digital), but it just gave an error after replacing the battery. So I don't know the current weight after surgery.
Now I need to figure out best to attach the 120mm fan to my (currently) 1 inch hole. I'm a little leary of making the hole exactly match the fan and directly attaching it (main concerns are about whether the bag would get caught in the fan). I'm also considering two fans vs one (at 79CFM, I'm still short of the computed 93 to 115 I need based on this calculator ). Luckily, I still have enough MDF for another base if I screw it up (on purpose -- I plan on making a "good" one once I work out all of the kinks with the original, but if I need it before then, I'm good).
Showing posts with label hoverroomba. Show all posts
Showing posts with label hoverroomba. Show all posts
Friday, June 27, 2008
Monday, June 16, 2008
3, 2, 1....Blastoff?
So, I disassembled the dust bin to extract the vacuum fan. Then, using the all-pupose attachment implement (aka duct tape) I secured the fan to the hovercraft.
Next, I had to find a way to turn on just the fan motor. I tried the SCI Tester program that you can get from the RooTooth people, but it only ran in safe mode (which was a problem because it didn't override the cliff sensors). Next, I tried the Microsoft Robotics Studio, but I couldn't get it to connect (I'll have to dig more). Finally, I found a program by "Black 64" - http://www.roombareview.com/chat/viewtopic.php?t=6941 that did the trick. I could send the 132 command (Full Mode) and then individually control each motor regardless of the cliff sensor status. The whirr of the motor sounded quite good at this point.
My first attempt was to just switch the leads and see if that switched the fan direction. Unfortunately, the circuit was smart enough to overcome that and continued to run in the "correct" direction which was the wrong direction for my intent. So my fan was sucking instead of blowing. So, I detached it and reoriented it so that it would then blow. Now set for a first flight.
So, it turns out that the Roomba fan motor isn't powerful enough to even lift the wooden platform off the ground, much less fully burdened with a 10lb Roomba. So I'll need to start investigating fan options and looking at stripping some weight off the Roomba. This is no longer going to be something that others could do without affecting the performance of their bot.
Images of the latest activity can be found here: http://www.flickr.com/photos/27513500@N04/sets/72157605657201637/
Next, I had to find a way to turn on just the fan motor. I tried the SCI Tester program that you can get from the RooTooth people, but it only ran in safe mode (which was a problem because it didn't override the cliff sensors). Next, I tried the Microsoft Robotics Studio, but I couldn't get it to connect (I'll have to dig more). Finally, I found a program by "Black 64" - http://www.roombareview.com/chat/viewtopic.php?t=6941 that did the trick. I could send the 132 command (Full Mode) and then individually control each motor regardless of the cliff sensor status. The whirr of the motor sounded quite good at this point.
My first attempt was to just switch the leads and see if that switched the fan direction. Unfortunately, the circuit was smart enough to overcome that and continued to run in the "correct" direction which was the wrong direction for my intent. So my fan was sucking instead of blowing. So, I detached it and reoriented it so that it would then blow. Now set for a first flight.
So, it turns out that the Roomba fan motor isn't powerful enough to even lift the wooden platform off the ground, much less fully burdened with a 10lb Roomba. So I'll need to start investigating fan options and looking at stripping some weight off the Roomba. This is no longer going to be something that others could do without affecting the performance of their bot.
Images of the latest activity can be found here: http://www.flickr.com/photos/27513500@N04/sets/72157605657201637/
Monday, June 9, 2008
Construction begins
This weekend, I started constructing my HoverRoomba. After a trip to the orange home improvement store (about $4.50 for the 2'x4' sheet of MDF), here's what I did:
1. First, I cut the MDF down to 2'x2' (gives me spare wood to make another one if needed).
2. Next, I found the center of the 2'x2' sqaure using the corner technique.
3. I drove a small nail into the center of the circle and used some rope to draw a 13" circle (the Roomba is 13" in diameter.
4. Next, I sanded the edges to keep them from tearing the plastic sheeting.
5. After that, I drilled a small hole in what will be the rear of the craft. This is where I will be mounting the vacuum fan.
6. I had some heavy plastic sheeting left over from installing floating laminate flooring (the roll was about $18 originally, but I'm only using a small amount); this plastic was taped to the bottom with about 3/4" of "play" all around. This is the hovercraft skirt.
7. Next, I used some of the scrap MDF to finish the skirt and form the air pocket that the craft will hover on, I attached it with two wood screws.
8. I cut two vent holes in the skirt for the air to pass from the skirt to the coushin. When I first cut them, I made them too big (one of the pictures shows me testing the skirt by blowing through the hole). I covered them with tape and made smaller slits which seemed to work much better.
http://www.flickr.com/photos/27513500@N04/
All of the pictures were taken by my 10-year old with her phone (2.0 megapixel), so composition is what it is.
My next steps are to fit it to the Roomba and fine tune the shape. Then, I will hook the vacuum fan to it and see if she'll go.
1. First, I cut the MDF down to 2'x2' (gives me spare wood to make another one if needed).
2. Next, I found the center of the 2'x2' sqaure using the corner technique.
3. I drove a small nail into the center of the circle and used some rope to draw a 13" circle (the Roomba is 13" in diameter.
4. Next, I sanded the edges to keep them from tearing the plastic sheeting.
5. After that, I drilled a small hole in what will be the rear of the craft. This is where I will be mounting the vacuum fan.
6. I had some heavy plastic sheeting left over from installing floating laminate flooring (the roll was about $18 originally, but I'm only using a small amount); this plastic was taped to the bottom with about 3/4" of "play" all around. This is the hovercraft skirt.
7. Next, I used some of the scrap MDF to finish the skirt and form the air pocket that the craft will hover on, I attached it with two wood screws.
8. I cut two vent holes in the skirt for the air to pass from the skirt to the coushin. When I first cut them, I made them too big (one of the pictures shows me testing the skirt by blowing through the hole). I covered them with tape and made smaller slits which seemed to work much better.
http://www.flickr.com/photos/27513500@N04/
All of the pictures were taken by my 10-year old with her phone (2.0 megapixel), so composition is what it is.
My next steps are to fit it to the Roomba and fine tune the shape. Then, I will hook the vacuum fan to it and see if she'll go.
Tuesday, May 27, 2008
And so it begins...
This blog will document the trials and tribulations that I experience as I attempt to convert a Roomba into an autonomous Hovercraft. Stay tuned for further posts.
Layne
Layne
Subscribe to:
Posts (Atom)
